Synthesis and electrochemical,electrochromic and electrical properties of novel s-triazine bridged trinuclear Zn(II), Cu(II) and Lu(III) and a tris double-decker Lu(III) phthalocyanines

The new s-triazine-bridged trinuclear Zn(II) and Cu(II) phthalocyanines have been synthesized from the reaction of corresponding anhydrous metal salts, Zn(OAc)₂ and CuCl with 4,5-bis(hexylthio)-phthalonitrile and 2,4,6-tris(2-thiophthalonitrile)-s-triazine. The tris phthalonitrile derivative of s-triazine was prepared from the reaction of 4-nitrophthalonitrile and thiocyanuric acid in dry dimethylformamide as solvent using K₂CO₃ as the base. The same route was applied to prepare the trinuclear Lu(III) phthalocyanine analogue. The conversion of tris phthalonitrile into its isoindoline derivative was accomplished by bubbling ammonia gas through a solution in methanol in the presence of sodium methoxide. The cyclization of two different isoindoline derivatives and 4,5-bis(hexylhthio)-1,2-diiminoisoindoline, with lutetium (III) acetate in dimethylformamide gave trinuclear Lu(III) phthalocyanine. The reaction of this complex with octakis-hexylthio phthalocyanine led to the isolation of tris double-decker Lu(III) phthalocyanine. The structures of the target compounds were confirmed by elemental analysis, UV–vis, IR and MALDI-TOF mass spectroscopies. The d.c. and a.c. conductivities of the phthalocyanine compounds were measured as a function of temperature. The small value of pre-exponential factor suggested the conduction by localized states in the band tails and by localized states near the Fermi level. The temperature dependence of the frequency exponent showed that the conduction in these compounds is due to hopping of charge carriers. The tris double-decker phthalocyanine complex showed well-defined electrochromic behaviour with green-blue and blue-purple colour transitions.     

Relationship between retinal lesions and axial length, age and sex in high myopia

Questionnaires (3426; 72.8%) and blood samples (3890; 82.6%) were analysed from 4704 women post-natally. The answers to the questionnaire confirmed that those patients living in areas with the highest percentage employed in agriculture were most likely to be in direct or indirect contact with sheep or sheep products. When the 788 (20.3%) of the sera with group specific antibody were examined for type-specific antibody, 291 (7.5%) reacted with Chlamydia trachomatis, 153 (3.9%) with Chlamydia pneumoniae, but only one (0.03%) with Chlamydia psittaci. Thus, it would appear that C. psittaci was not an important pathogen in this survey, despite the largest proportion of blood samples being submitted from those most likely to be employed in agriculture. However, in the course of this survey the three patients who had previously suffered chlamydia-associated abortion had successful pregnancies and submitted blood specimens. Serological studies on the serial bloods from these patients showed that, despite developing antibody to the C. psittaci pool and the ovine abortion strain of C. psittaci following abortion, this antibody waned. At the time of the subsequent successful pregnancy, serological results would not have detected a previous C. psittaci infection, but one due to C. pneumoniae. Thus, the results of a survey such as this must be interpreted with caution.     

Epidermoid cyst of the brain stem. Case report

OBJECTIVE: To search for the effect and safety of coral porous hydroxyapatite (CHA) implanted material in orbital rim reconstruction. METHODS: 7 cases of orbital rim reconstruction were treated with CHA which is a plate form mass with an interconnected system of canals of approximately 200 microns in size. It has three types: 1.0 cm x 1.5 cm x 5.0 cm, 0.6 cm x 1.5 cm x 5.0 cm and 0.4 cm x 1.5 cm x 5.0 cm. According to the shape of a contralateral healthy orbit, a rubber putty model was made before the operation. An incision was designed at the upper 1/3 of the face for the elimination of wrinkles or a prolonged incision of lower lid bag plastic surgery was made. After the exposure of the defective part of the orbit, a correctly molded CHA tamponade was inserted. RESULTS: The orbital rim reconstruction in 7 cases with orbital defect was successfully treated with CHA. During a follow-up of 3-12 months (average 6.6 months), there was no extrusion or migration of implant. CONCLUSION CHA is a good material for substitution of bone graft and is much better than autogenous tissue of other artificial materials.     

A processable rainbow mimic fluorescent polymer and its unprecedented coloration efficiency in electrochromic device

A processable rainbow mimic fluorescent polymer (PSNSF) based on 1-(9H-fluoren-2-yl)-2,5-di(thiophen-2-yl)-1H-pyrrole (SNSF) was synthesized via electrochemical polymerization in a mixture of ethanol and CH₂Cl₂ solution containing 0.1 M LiClO₄. Characterization was carried out using cyclic voltammetry, UV-vis and FT-IR spectroscopic techniques. Also, an electrochromic device based on PSNSF was studied, which exhibits high coloration efficiency (CE), high redox stability (retaining 98.6% of its optical activity after 4000th switch) and very low response time (less than 0.5 s).     

Rubber effect on metallic dampers used on the supports of steel cross members

There are many strengthening methods made with steel cross members for strengthening the structures with inadequate earthquake behavior. This type of strengthening methods is also effective in buckling of the cross members in the behavior of the structural frames. This buckling may cause partial or complete collapse of the structure. Thus, it is quite important to prevent and limit the formation of buckling in steel crosses. At the TEC 2018, the insulation unit is defined as the elements that can exhibit flexible behavior on the horizontal direction and rigid behavior on the vertical direction under the effect of earthquake loads. The basic principle of using insulation units is that these members can dissipate energy in the carrier system. The originality of this study is to experimentally investigate the damper behavior created by using cylindrical rubber wedges, which can be easily found in the automotive industry, in combination with steel plates and bolts. In this experimental study, the contribution of seismic insulators to the structural element to be strengthened was investigated. The insulators used in this study are considered by analogy with lead-core rubber insulators. As such seismic lead-core rubber insulators move under the influence of lateral loads, the lead core inside makes plastic deformation, thus increasing the damping rate. In this insulator study, it is aimed to use U plates or bolts instead of lead core. While vertical loads are covered by rubber support, horizontal loads will be damped due to plastic deformation of U plates or bolts. The five types of seismic dampers were used as 10 B-type rubber wedge mounted damper (SR), 2 U-type steel plates damper (SP), 10 M6 steel bolted damper (SB), 2 U-type steel plates and 10 B-type rubber wedge mounted damper (SPR), 10 M6 steel bolted, and 10 C-type rubber wedge mounted damper (SBR). These specimens were tested under lateral loading and constant vertical loading. The results obtained at the end of the tests shall be compared considering the strength, stiffness, and dissipated energy capacities of the specimens.     

Investigating the benefits of using circular die springs instead of rectangular die springs

Die springs with rectangular cross section (rectangular die springs) are common in the industry. However, the production of rectangular die springs is difficult, and the cost of production is high. In this study, we examined the use of die springs with circular cross section (circular die springs), which are both easier to produce and less costly, in place of rectangular ones. To this aim, the fatigue life values of both die spring with equivalent specifications were compared experimentally. The results obtained were transferred to the finite element methods software to run the simulation of the fatigue test. From the experimental results obtained, it has been observed that using circular die springs in place of rectangular die springs is always possible, provided that the springs are guided with cast polyamide guides.     

Estimation of real GDP and unrecorded economy in Turkey based on environmental data

This paper estimates the real gross domestic product (GDP) and unrecorded economy for Turkey using the Kalman filter technique. Using different tests, most of the research articles on energy policy investigate the causal relationship between energy consumption and GDP for different countries. On the other hand, other studies on climate change try to show the effects of both energy consumption and GDP on carbon dioxide (CO₂) emission. Since the unreported economy has an important weight in developing countries where the recorded (or official) GDP suffers from considerable measurement problems, investigation of the relationship between the recorded GDP and energy consumption may lead to biased results. In this paper, the economic variables (GDP, country population) as well as environmental variables (CO₂ emission, forest area) are used in order to estimate GDP, which is an unobserved variable in our model. The results clearly indicate that: first, the true GDP in Turkey, that our model estimates, is higher than the observed (recorded) GDP in the whole period of observation (1973–2003) and the size of unrecorded economy varies between 12 and 30 percent of the observed GDP; second, the gap between the true GDP and the observed GDP has an increasing trend; third, if the change in GDP per primary energy supply is smaller than the change in CO₂ per primary energy supply, then there may exist unrecorded economy.     

The effects of the welding current on heat input,nugget geometry,and the mechanical and fractural properties of resistance spot welding on Mg/Al dissimilar materials

Investigating the joining capability of magnesium AZ31 alloy sheets and aluminium 1350 alloy sheets with the application of resistance spot welding was the objective of this study. The weld current values used in the welding process of Al–Mg sheets were 22, 23, 25, 27, 29, 31, and 33 kA. The studies examined the nugget geometries of joined specimens, recorded the scanning electron microscopy (SEM) images of the welded zone and the fracture surface, and recorded the energy-dispersive spectroscopy (EDS, semi-quantitative) analyses. The results of the experiment confirmed that nugget geometry was different for the Al and Mg sides. Tensile shear tests carried out on the welded joints determined their strength and failure mode. The increase in the weld current and duration resulted in an increase in the nugget size and the weld strength. According to observations, the tensile load bearing capacity (TLBC) increased up to 29 kA of the weld current value. It was also found that tearing during fracture occurred in two different ways.     

A risk analysis model for radioactive wastes

Hazardous wastes affect natural environmental systems to a significant extend, and therefore, it is necessary to control their harm through risk analysis. Herein, an effective risk methodology is proposed by considering their uncertain behaviors on stochastic, statistical and probabilistic bases. The basic element is attachment of a convenient probability distribution function (pdf) to a given waste quality measurement sequence. In this paper, (40)K contaminant measurements are adapted for risk assessment application after derivation of necessary fundamental formulations. The spatial contaminant distribution of (40)K is presented in the forms of maps and three-dimensional surfaces.     

Genetic algorithm‐based scheduling in cognitive radio networks under interference temperature constraints

The proliferation of wireless technologies and services has intensified the demand for the radio spectrum. However, the currently existing fixed spectrum assignment policy leads to an inefficient and unevenly distributed spectrum utilization. Cognitive radio paradigm has been proposed to alleviate these drawbacks by employing dynamic spectrum access (DSA) methodology. Federal Communications Commission (FCC) has proposed the interference temperature model, which enables the unlicensed users to utilize the licensed frequencies simultaneously with the licensed users as long as they conform to the interference temperature constraints. Recently, throughput and delay optimal schedulers that meet the interference temperature constraints in cognitive radio networks have been formulated in the literature. However, these schedulers have high computational complexity. In this paper, we propose genetic algorithm (GA)‐based suboptimal methods addressing these throughput and delay optimal scheduling problems. The simulation results corroborate that our GA‐based approach yields very close performance to the optimal solutions and operates with much lower complexity. Copyright © 2010 John Wiley & Sons, Ltd.